-
DI Socket fittings
Fittings for socket joints
Collar T type and K type
Double Socket Bend 90° (1/4)
Double Socket Bend 45° (1/8)
Double Socket Bend 22.5° (1/16)
Double Socket Bend 11.25° (1/32)
All socket tee
All socket tee with 45°Angle branch
Double-socket tee with flanged branch
Double socket taper
All socket crossing
Others
Socket-spigot fittings
Flanged socket
Flanged spigot
Caps -
DI Flanged fittings
Fittings for flanged joints
Double Flanged Bend 90° (1/4)
Double Flanged Duckfoot Bend 90° (1/4)
Double Flanged Long radius Bend 90° (1/4)
Double Flanged Bend 45° (1/8)
Double Flanged Bend 22.5° (1/16)
Double Flanged Bend 11.25° (1/32)
All Flanged tee
All Flanged tee with 45°Angle branch
All Flanged crossing
Double flanged taper
Blank Flange
Reducing Flanges
Others
Socket-spigot fittings
Flanged socket
Flanged spigot
Caps -
No Hub-SML DS Offset Bend
DS CAST IRON Off-set
Cast Iron Fixed Offset Bend is available with a 130mm projection, and is used to direct a soil system around cornered obstructions, whilst keeping the system parallel. The bend is manufactured to EN877 using solid cast iron and finished with a Epoxy paint coating that complements the aesthetic of period buildings. -
No Hub-SML Cap with Rubber Seal
It is constructed of high quality cast iron. It is easy to install.
For use where a watertight seal is needed -
No Hub-SML 45°Single branch
Used to bring horizontal and vertical pipe runs together, usually when connecting a pipe from a WC into the main soil stack. The 135 degree angle introduces a steeper fall to the horizontal run than a standard 92.5 or 112.5 degree branch. It is most commonly found on the outside wall of a building, often on blocks of flats or apartments. -
No Hub-SML 88°Large Radius Bend with Access Door
SML 88°Large Radius Bend with Access Door, foul and surface water drainage system
Includes a wide variety of components, such as Bends, Junctions, Rodding Access and Access Fittings, together with Inspection Chambers and Manhole Bases.
-
No Hub-SML 88°Large bend
Cast Iron SML 88°Large bend
Cast Iron SML is a dry-jointed, lightweight cast iron drainage system, primarily used for above ground soil and waste drainage but also for rainwater installations
High strength, low maintanence system
Quick to assemble
Agrement EN 877 -
No Hub-SML Top bend
EN877 SML Top bend
Material: Grey Cast Iron
Coating: SML,KML,BML,TML
Product description：The pipe fittings have smooth surface, high density and strength, reasonable design in structure, beautiful externality used on high buildings and environmental protecting. -
No Hub-SML Vent bend
SML Vent bend
Material: Grey Cast Iron
Coating: SML,KML,BML,TML
Product description：The pipe fittings have smooth surface, high density and strength, reasonable design in structure, beautiful externality used on high buildings and environmental protecting.
-
No Hub-SML 45°Bend
Cast Iron SML 45°Bend Cast iron
Cast Iron SML is a dry-jointed, lightweight cast iron drainage system, primarily used for above ground soil and waste drainage but also for rainwater installations
High strength, low maintanence system
Quick to assemble
Agrement EN 877 -
floor drain
A floor drain is a plumbing fixture that is installed in the floor of a structure, mainly designed to remove any standing water near it.
Floor drain DN200*100 -
No Hub-SML 88° Bend with 250mm
Dimensions
Size : 250mm
Bend Angle : 88°
Description
Easy to install our Sewer drainage range includes solid pipe and fittings. A combined lip and compression seal into its solid pipe which is secure against dislodgement and makes jointing easier ensuring that joints remain leak free for years to come.